Kp-51hw40 manual

CN17, 18, If removed, it may cause liquid spill. Receive the Monoscope signal. Set generator to crosshatch. Cover the both red and blue picture lenses with the lens caps 2. Receive the monoscope signal. Setup for Adjustment 1. Data Setting Turn on the power and wait for 10 minutes. Operation Method for Fine Adjustment Make sure that the adjustment for NTSC Full mode finished 15 Make fine adjustment so that horizontal lines and vertical and the data have already been written.

Receive the signal. Connect an oscilloscope between CN5 7 pin B on the A board and ground. Ne les remplacer que par une Replace only with part number piece portant le numero specifie.

Page The model and serial numbers are located at the rear of the Never pull on the cord. Page Important Safeguards Important Safeguards Overloading Do not overload wall outlets, extension For your protection, please read these instructions cords or convenience receptacles completely, and keep this manual for future reference.

Carefully observe and comply with all warnings, cautions and instructions placed on the set or described in the Always turn the set off when it is not Page Installation Power-Cord Protection Do not allow anything to rest on or roll Water and Moisture over the power cord, and do not place the Do not use power-line operated sets set where the power cord is subject to near water — for example, near a wear or abuse.

Page Lightning Safety Check For added protection for this television receiver during a Upon completion of any service or repairs lightning storm, or when it is left unattended and unused to the set, ask the service technician to for long periods of time, unplug it from the wall outlet perform routine safety checks as specified and disconnect the antenna.

Model KPHW40 is used for illustration purposes. No peripheral cables are included. If you intend to add additional equipment to your projection TV, please check the hookup instructions for your desired setup before you begin. Push into connection. Pressing brings up the on-screen menus.

MENU The arrow buttons move the on-screen cursor in the menus and by pressing the Select button selects the menu item. Newer to Cable or an homes are equipped with standard coaxial cable see ; Disconnect all power sources before making any connections. Be sure to read the Using three separate component video cables, connect the Digital TV Set-top box manual. The Auto Setup screen appears when you turn your projection TV on for the first time after installing it. If you do not want to set up the channels at this time, you can do it later by using the Auto Program feature in the Channel menu see page If they do not converge, the color is poor and the picture blurs.

Before you use your projection TV, be sure to adjust the convergence. Page Using The Features Using the Features Using the Remote Control The following table describes the buttons on the remote control that are for more advanced functions. The following will explain the function of some of the buttons found on your remote control.

To turn the display off, press again. If you select as a in the Setup menu, your projection TV This projection TV is capable of receiving the i, p, p and i digital TV formats. The factory setting for Favorite Channel is Auto. You can also change the size of both the left and right pictures. The next time you use the Twin View feature the memorized sizes appear.

Page Using the Features Changing the The zoom feature lets you change the size of the left and right pictures. Picture Size To enlarge the left To enlarge the picture reduce right picture the right reduce the left 1 1 1 1 1 1 1 1 Move the Move the To use the Scrolling Channel Index function 1 1 1 1 Press Page Using the Features 4 4 4 4 Press The selected channel will be enlarged for normal viewing.

To cancel Scrolling Channel Index Press again to resume normal viewing. MENU 2 2 2 2 Move the joystick to the desired menu icon and press to select it.

Reality Interlaced Recommended for moving pictures. Creation Progressive Recommended for still images and text. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recom mend their replacement. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. Check the condition of the monopole antenna if any.

Make sure the end is not broken off, and has the plastic cap on it. Point out the danger of impalement on a broken antenna to the customer, and recommend the antenna's replacement. Make sure your instruments are accurate;be suspicious of your HV meter if sets always have low HV. Check the antenna temminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage.

Check leakage as described below. Leak- age current can be measured by any one of three methods. Follow the manufacturers' instructions to usc these instruments. A battery-operated AC milliammeter.

The Data Precision digital multimeter is suitable for this job. The "limit" indica- tion is 0. NearIy all bat- tery operated digital multimeters that have a 2V AC range are suitable.

See Fig. If the retaining screw is to be used as your earth-ground, verify that it is at ground by measuring the resistance between it and a cold- water pipe with an ohmmeter. The reading should be zero ohms. If a cold-water pipe is not accessible, connect a l00 watts trouble light not a neon lamp between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side of the line, the lamp should light at normal brilliance if the screw is at ground potential.

Using an AC voltmeter to check AC leakage. Checking for earth ground. No revisions or updates are applicable at this time. Reissued to show corrected Page Correction to Exploded View Cover parts list to indicated location and. After correcting the original service problem, perfom the follow-. Check the area of your repair for unsoldered or poorly-sol-.